-
ATUP 100
vertical nc table
Technical information
Faceplate diameter min.
mm
100
Axis of rotation
./.
vert.
Load capacity
kg
120
Max. revolutions per minute
Rpm
80
Bearing diameter
mm
120 x 70
Worm gear ratio
./.
36
Max. center bore diameter
mm
35
Drive torque
Nm
3
Unit weight
kg
20
Max. tilting moment at the axis of rotation
Nm
200
Max. axial load
N
2.000
Max. mass moment of inertia
kgm²
1,4
Max. tangential torque with clamping actuated
Nm
80
Max. tangential torque without clamping
Nm
115
Clamping type
./.
pneu.
Max. clamping pressure
bar ü
6
Dividing accuracy at the worm drive
''
+/- 30
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,02
Rectangularity including wobble
mm
Table height
mm
125
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 200
vertical nc table
Technical information
ATU 200
Axis vert.
Axis horiz.
Faceplate diameter min.
mm
200
mm
200
Axis of rotation
./.
vert.
./.
horiz.
Load capacity
kg
600
kg
200
Max. revolutions per minute
Rpm
50
Rpm
50
Bearing diameter
mm
170 x 130
mm
170 x 130
Worm gear ratio
./.
60
./.
60
Max. center bore diameter
mm
70
mm
70
Drive torque
Nm
10
Nm
10
Unit weight
kg
70
kg
70
Max. tilting moment at the axis of rotation
Nm
3.200
Nm
2.000
Max. axial load
N
25.000
N
15.000
Max. mass moment of inertia
kgm²
20
kgm²
20
Max. tangential torque with clamping actuated
Nm
1.200
Nm
1.200
Max. tangential torque without clamping
Nm
700
Nm
700
Clamping type
./.
hydrau.
./.
hydrau.
Max. clamping pressure
bar ü
63
bar ü
63
Dividing accuracy at the worm drive
''
+/- 15
''
+/- 15
Dividing accuracy with direct mounted encoder
''
+/- 3
''
+/- 3
Repeatability
''
+/- 1
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
mm
0,01
Plain parallelism including wobble
mm
0,01
mm
Rectangularity including wobble
mm
mm
0,02
Table height
mm
160
mm
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATUP 200
vertical nc table
Technical information
ATUP 200
Axis horiz.
Axis vert.
Faceplate diameter min.
mm
200
mm
200
Axis of rotation
./.
horiz.
./.
vert.
Load capacity
kg
200
kg
600
Max. revolutions per minute
Rpm
50
Rpm
50
Bearing diameter
mm
170 x 130
mm
170 x 130
Worm gear ratio
./.
60
./.
60
Max. center bore diameter
mm
70
mm
70
Drive torque
Nm
10
Nm
10
Unit weight
kg
70
kg
70
Max. tilting moment at the axis of rotation
Nm
2.000
Nm
3.200
Max. axial load
N
15.000
N
25.000
Max. mass moment of inertia
kgm²
20
kgm²
20
Max. tangential torque with clamping actuated
Nm
930
Nm
930
Max. tangential torque without clamping
Nm
700
Nm
700
Clamping type
./.
pneu.
./.
pneu.
Max. clamping pressure
bar ü
6
bar ü
6
Dividing accuracy at the worm drive
''
+/- 15
''
+/- 15
Dividing accuracy with direct mounted encoder
''
+/- 3
''
+/- 3
Repeatability
''
+/- 1
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
mm
0,01
Plain parallelism including wobble
mm
mm
0,01
Rectangularity including wobble
mm
0,02
mm
Table height
mm
mm
170
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 280
vertical nc table
Technical information
ATU 280
Axis vert.
Axis horiz.
Faceplate diameter min.
mm
280
mm
280
Axis of rotation
./.
verti.
./.
horiz.
Load capacity
kg
800
kg
250
Max. revolutions per minute
Rpm
33
Rpm
33
Bearing diameter
mm
230 x 155
mm
230 x 155
Worm gear ratio
./.
72
./.
72
Max. center bore diameter
mm
100
mm
100
Drive torque
Nm
12
Nm
12
Unit weight
kg
140
kg
140
Max. tilting moment at the axis of rotation
Nm
5.000
Nm
3.200
Max. axial load
N
30.000
N
17.000
Max. mass moment of inertia
kgm²
40
kgm²
40
Max. tangential torque with clamping actuated
Nm
2.100
Nm
2.100
Max. tangential torque without clamping
Nm
1.200
Nm
1.200
Clamping type
./.
hydrau.
./.
hydrau.
Max. clamping pressure
bar ü
63
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
''
+/- 3
Repeatability
''
+/- 1
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
mm
0,01
Plain parallelism including wobble
mm
0,01
mm
Rectangularity including wobble
mm
mm
0,02
Table height
mm
195
mm
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 400
vertical nc table
Technical information
ATU 400
Axis vert.
Axis horiz.
Faceplate diameter min.
mm
400
mm
400
Axis of rotation
./.
verti.
./.
horiz.
Load capacity
kg
1.500
kg
500
Max. revolutions per minute
Rpm
25
Rpm
25
Bearing diameter
mm
385 x 260
mm
385 x 260
Worm gear ratio
./.
180
./.
180
Max. center bore diameter
mm
150
mm
150
Drive torque
Nm
18
Nm
18
Unit weight
kg
320
kg
320
Max. tilting moment at the axis of rotation
Nm
12.000
Nm
5.200
Max. axial load
N
40.000
N
25.000
Max. mass moment of inertia
kgm²
300
kgm²
300
Max. tangential torque with clamping actuated
Nm
4.600
Nm
4.600
Max. tangential torque without clamping
Nm
2.000
Nm
2.000
Clamping type
./.
hydrau.
./.
hydrau.
Max. clamping pressure
bar ü
63
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
''
+/- 3
Repeatability
''
+/- 1
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
mm
0,01
Plain parallelism including wobble
mm
0,01
mm
Rectangularity including wobble
mm
mm
0,02
Table height
mm
230
mm
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 520
vertical nc table
Technical information
Faceplate diameter min.
mm
520
Axis of rotation
./.
verti.
Load capacity
kg
3.000
Max. revolutions per minute
Rpm
12
Bearing diameter
mm
450 x 325
Worm gear ratio
./.
180
Max. center bore diameter
mm
200
Drive torque
Nm
18
Unit weight
kg
480
Max. tilting moment at the axis of rotation
Nm
16.000
Max. axial load
N
60.000
Max. mass moment of inertia
kgm²
740
Max. tangential torque with clamping actuated
Nm
5.000
Max. tangential torque without clamping
Nm
3.400
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,01
Rectangularity including wobble
mm
Table height
mm
230
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 630
vertical nc table
Technical information
Faceplate diameter min.
mm
630
Axis of rotation
./.
verti.
Load capacity
kg
4.000
Max. revolutions per minute
Rpm
12
Bearing diameter
mm
525 x 395
Worm gear ratio
./.
180
Max. center bore diameter
mm
290
Drive torque
Nm
18
Unit weight
kg
880
Max. tilting moment at the axis of rotation
Nm
23.000
Max. axial load
N
80.000
Max. mass moment of inertia
kgm²
1.200
Max. tangential torque with clamping actuated
Nm
12.000
Max. tangential torque without clamping
Nm
5.400
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,01
Rectangularity including wobble
mm
Table height
mm
280
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 800
vertical nc table
Technical information
Faceplate diameter min.
mm
800
Axis of rotation
./.
verti.
Load capacity
kg
7.000
Max. revolutions per minute
Rpm
10
Bearing diameter
mm
600 x 460
Worm gear ratio
./.
180
Max. center bore diameter
mm
340
Drive torque
Nm
50
Unit weight
kg
1.200
Max. tilting moment at the axis of rotation
Nm
32.000
Max. axial load
N
120.000
Max. mass moment of inertia
kgm²
1.700
Max. tangential torque with clamping actuated
Nm
16.000
Max. tangential torque without clamping
Nm
8.500
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,01
Rectangularity including wobble
mm
Table height
mm
300
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 1000
vertical nc table
Technical information
Faceplate diameter min.
mm
1000
Axis of rotation
./.
verti.
Load capacity
kg
12.000
Max. revolutions per minute
Rpm
9
Bearing diameter
mm
870 x 650
Worm gear ratio
./.
180
Max. center bore diameter
mm
450
Drive torque
Nm
50
Unit weight
kg
2.200
Max. tilting moment at the axis of rotation
Nm
60.000
Max. axial load
N
180.000
Max. mass moment of inertia
kgm²
5.400
Max. tangential torque with clamping actuated
Nm
27.500
Max. tangential torque without clamping
Nm
23.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,02
Rectangularity including wobble
mm
Table height
mm
360
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 1250
vertical nc table
Technical information
Faceplate diameter min.
mm
1.250
Axis of rotation
./.
verti.
Load capacity
kg
18.000
Max. revolutions per minute
Rpm
9
Bearing diameter
mm
1.095 x 850
Worm gear ratio
./.
180
Max. center bore diameter
mm
600
Drive torque
Nm
50
Unit weight
kg
3.700
Max. tilting moment at the axis of rotation
Nm
90.000
Max. axial load
N
250.000
Max. mass moment of inertia
kgm²
9.600
Max. tangential torque with clamping actuated
Nm
40.000
Max. tangential torque without clamping
Nm
36.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,03
Rectangularity including wobble
mm
Table height
mm
370
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 1600
vertical nc table
Technical information
Faceplate diameter min.
mm
1.600
Axis of rotation
./.
verti.
Load capacity
kg
26.000
Max. revolutions per minute
Rpm
4
Bearing diameter
mm
1.300 x 1.030
Worm gear ratio
./.
180
Max. center bore diameter
mm
700
Drive torque
Nm
70
Unit weight
kg
5.400
Max. tilting moment at the axis of rotation
Nm
160.000
Max. axial load
N
400.000
Max. mass moment of inertia
kgm²
17.000
Max. tangential torque with clamping actuated
Nm
46.000
Max. tangential torque without clamping
Nm
76.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,05
Rectangularity including wobble
mm
Table height
mm
550
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
ATU 2000
vertical nc table
Technical information
Faceplate diameter min.
mm
2.000
Axis of rotation
./.
verti.
Load capacity
kg
50.000
Max. revolutions per minute
Rpm
3
Bearing diameter
mm
1.850 x 1.500
Worm gear ratio
./.
201:2
Max. center bore diameter
mm
800
Drive torque
Nm
110
Unit weight
kg
12.000
Max. tilting moment at the axis of rotation
Nm
300.000
Max. axial load
N
540.000
Max. mass moment of inertia
kgm²
35.000
Max. tangential torque with clamping actuated
Nm
117.000
Max. tangential torque without clamping
Nm
150.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Plain parallelism including wobble
mm
0,05
Rectangularity including wobble
mm
Table height
mm
1.000
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
Choose your language
