-
AWU 100
Horizontal nc table
Technical information
Faceplate diameter min.
mm
100
Axis of rotation
./.
horiz.
Load capacity
kg
80
Max. revolutions per minute
Rpm
80
Bearing diameter
mm
120 x 70
Worm gear ratio
./.
36
Max. center bore diameter
mm
35
Drive torque
Nm
3
Unit weight
kg
26
Max. tilting moment at the axis of rotation
Nm
200
Max. axial load
N
2.000
Max. mass moment of inertia
kgm²
1,4
Max. tangential torque with clamping actuated
Nm
150
Max. tangential torque without clamping
Nm
115
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 30
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
125
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWUP 100
Horizontal nc table
Technical information
Faceplate diameter min.
mm
100
Axis of rotation
./.
horiz.
Load capacity
kg
80
Max. revolutions per minute
Rpm
80
Bearing diameter
mm
120 x 70
Worm gear ratio
./.
36
Max. center bore diameter
mm
35
Drive torque
Nm
3
Unit weight
kg
26
Max. tilting moment at the axis of rotation
Nm
200
Max. axial load
N
2.000
Max. mass moment of inertia
kgm²
1,4
Max. tangential torque with clamping actuated
Nm
80
Max. tangential torque without clamping
Nm
115
Clamping type
./.
pneu.
Max. clamping pressure
bar g
6
Dividing accuracy at the worm drive
''
+/- 30
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
125
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWU 160
Horizontal nc table
Technical information
Faceplate diameter min.
mm
160
Axis of rotation
./.
horiz.
Load capacity
kg
150
Max. revolutions per minute
Rpm
100
Bearing diameter
mm
146 x 80
Worm gear ratio
./.
30
Max. center bore diameter
mm
40
Drive torque
Nm
7
Unit weight
kg
62
Max. tilting moment at the axis of rotation
Nm
1.200
Max. axial load
N
5.000
Max. mass moment of inertia
kgm²
6,4
Max. tangential torque with clamping actuated
Nm
900
Max. tangential torque without clamping
Nm
650
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 15
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
165
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data.
The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWUP 160
Horizontal nc table
Technical information
Faceplate diameter min.
mm
160
Axis of rotation
./.
horiz.
Load capacity
kg
150
Max. revolutions per minute
Rpm
100
Bearing diameter
mm
146 x 80
Worm gear ratio
./.
30
Max. center bore diameter
mm
40
Drive torque
Nm
7
Unit weight
kg
62
Max. tilting moment at the axis of rotation
Nm
1.200
Max. axial load
N
5.000
Max. mass moment of inertia
kgm²
6,4
Max. tangential torque with clamping actuated
Nm
800
Max. tangential torque without clamping
Nm
650
Clamping type
./.
pneu.
Max. clamping pressure
bar g
6
Dividing accuracy at the worm drive
''
+/- 15
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
165
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data.
The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWU 200
Horizontal nc table
Technical information
Faceplate diameter min.
mm
200
Axis of rotation
./.
horiz.
Load capacity
kg
280
Max. revolutions per minute
Rpm
50
Bearing diameter
mm
190 x 130
Worm gear ratio
./.
72
Max. center bore diameter
mm
105
Drive torque
Nm
10
Unit weight
kg
90
Max. tilting moment at the axis of rotation
Nm
2.500
Max. axial load
N
10.000
Max. mass moment of inertia
kgm²
21,3
Max. tangential torque with clamping actuated
Nm
1.400
Max. tangential torque without clamping
Nm
750
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
170
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data.
The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWUP 200
Horizontal nc table
Technical information
Faceplate diameter min.
mm
200
Axis of rotation
./.
horiz.
Load capacity
kg
280
Max. revolutions per minute
Rpm
50
Bearing diameter
mm
190 x 130
Worm gear ratio
./.
72
Max. center bore diameter
mm
50
Drive torque
Nm
10
Unit weight
kg
90
Max. tilting moment at the axis of rotation
Nm
2.500
Max. axial load
N
10.000
Max. mass moment of inertia
kgm²
21,3
Max. tangential torque with clamping actuated
Nm
900
Max. tangential torque without clamping
Nm
750
Clamping type
./.
pneu.
Max. clamping pressure
bar g
6
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
170
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data.
The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWU 280
Horizontal nc table
Technical information
Faceplate diameter min.
mm
280
Axis of rotation
./.
horiz.
Load capacity
kg
400
Max. revolutions per minute
Rpm
33
Bearing diameter
mm
230 x 155
Worm gear ratio
./.
90
Max. center bore diameter
mm
120
Drive torque
Nm
12
Unit weight
kg
160
Max. tilting moment at the axis of rotation
Nm
4.000
Max. axial load
N
20.000
Max. mass moment of inertia
kgm²
47,3
Max. tangential torque with clamping actuated
Nm
2.100
Max. tangential torque without clamping
Nm
1.200
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
210
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
AWU 355
Horizontal nc table
Technical information
Faceplate diameter min.
mm
355
Axis of rotation
./.
horiz.
Load capacity
kg
650
Max. revolutions per minute
Rpm
30
Bearing diameter
mm
310 x 195
Worm gear ratio
./.
90
Max. center bore diameter
mm
150
Drive torque
Nm
18
Unit weight
kg
270
Max. tilting moment at the axis of rotation
Nm
6.500
Max. axial load
N
30.000
Max. mass moment of inertia
kgm²
100
Max. tangential torque with clamping actuated
Nm
3.000
Max. tangential torque without clamping
Nm
1.700
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
230
Many options and modifications are available to enhance the standard designs.
We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data.
The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011 -
AWU 520
Horizontal nc table
Technical information
Faceplate diameter min.
mm
520
Axis of rotation
./.
horiz.
Load capacity
kg
1.200
Max. revolutions per minute
Rpm
12
Bearing diameter
mm
450 x 325
Worm gear ratio
./.
180
Max. center bore diameter
mm
190
Drive torque
Nm
27
Unit weight
kg
811
Max. tilting moment at the axis of rotation
Nm
16.000
Max. axial load
N
50.000
Max. mass moment of inertia
kgm²
740
Max. tangential torque with clamping actuated
Nm
6.000
Max. tangential torque without clamping
Nm
3.400
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
350
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
AWU 630
Horizontal nc table
Technical information
Faceplate diameter min.
mm
650
Axis of rotation
./.
horiz.
Load capacity
kg
2.000
Max. revolutions per minute
Rpm
12
Bearing diameter
mm
525 x 395
Worm gear ratio
./.
180
Max. center bore diameter
mm
250
Drive torque
Nm
27
Unit weight
kg
1.250
Max. tilting moment at the axis of rotation
Nm
25.000
Max. axial load
N
80.000
Max. mass moment of inertia
kgm²
1.480
Max. tangential torque with clamping actuated
Nm
12.000
Max. tangential torque without clamping
Nm
5.400
Clamping type
./.
hydraul.
Max. clamping pressure
bar g
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,02
Center height
mm
380
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant.
Please note the preface - Partial extractions from the data sheets may lead to an incorrect equipment selection and specification. Rev.4.2 / 15.12.2011
-
AWU 800
Horizontal nc table
Technical information
Faceplate diameter min.
mm
800
Axis of rotation
./.
horiz.
Load capacity
kg
3.000
Max. revolutions per minute
Rpm
10
Bearing diameter
mm
750 x 580
Worm gear ratio
./.
180
Max. center bore diameter
mm
400
Drive torque
Nm
50
Unit weight
kg
1.800
Max. tilting moment at the axis of rotation
Nm
38.000
Max. axial load
N
100.000
Max. mass moment of inertia
kgm²
3.080
Max. tangential torque with clamping actuated
Nm
25.000
Max. tangential torque without clamping
Nm
14.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,03
Center height
mm
520
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant. Please note the preface. Partial extractions from the data sheets may lead to an incorrect equipment selection and specification.
Rev.4.2 / 15.12.2011 -
AWU 1000
Horizontal nc table
Technical information
Faceplate diameter min.
mm
1.000
Axis of rotation
./.
horiz.
Load capacity
kg
6.000
Max. revolutions per minute
Rpm
9
Bearing diameter
mm
870 x 650
Worm gear ratio
./.
180
Max. center bore diameter
mm
400
Drive torque
Nm
50
Unit weight
kg
3.500
Max. tilting moment at the axis of rotation
Nm
50.000
Max. axial load
N
120.000
Max. mass moment of inertia
kgm²
5.400
Max. tangential torque with clamping actuated
Nm
27.500
Max. tangential torque without clamping
Nm
23.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,04
Center height
mm
650
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant. Please note the preface. Partial extractions from the data sheets may lead to an incorrect equipment selection and specification.
Rev.4.2 / 15.12.2011
-
AWU 1250
Horizontal nc table
Technical information
Faceplate diameter min.
mm
1.250
Axis of rotation
./.
horiz.
Load capacity
kg
9.000
Max. revolutions per minute
Rpm
9
Bearing diameter
mm
1.095 x 850
Worm gear ratio
./.
180
Max. center bore diameter
mm
500
Drive torque
Nm
50
Unit weight
kg
5.500
Max. tilting moment at the axis of rotation
Nm
70.000
Max. axial load
N
180.000
Max. mass moment of inertia
kgm²
9.600
Max. tangential torque with clamping actuated
Nm
40.000
Max. tangential torque without clamping
Nm
36.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,04
Center height
mm
650
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant. Please note the preface. Partial extractions from the data sheets may lead to an incorrect equipment selection and specification.
Rev.4.2 / 15.12.2011 -
AWU 1600
Horizontal nc table
Technical information
Faceplate diameter min.
mm
1.600
Axis of rotation
./.
horiz.
Load capacity
kg
13.000
Max. revolutions per minute
Rpm
4
Bearing diameter
mm
1.300 x 1.030
Worm gear ratio
./.
320
Max. center bore diameter
mm
700
Drive torque
Nm
70
Unit weight
kg
8.700
Max. tilting moment at the axis of rotation
Nm
110.000
Max. axial load
N
260.000
Max. mass moment of inertia
kgm²
17.000
Max. tangential torque with clamping actuated
Nm
46.000
Max. tangential torque without clamping
Nm
40.000
Clamping type
./.
hydrau.
Max. clamping pressure
bar ü
63
Dividing accuracy at the worm drive
''
+/- 10
Dividing accuracy with direct mounted encoder
''
+/- 3
Repeatability
''
+/- 1
Concentricity of the pilot diameter
mm
0,01
Rectangularity including wobble
mm
0,05
Center height
mm
850
Many options and modifications are available to enhance the standard designs. We will gladly quote to your specific requirements. Please contact us.
We reserve the right for technical alterations and do not guarantee the correctness of indicated data. The dimensions can vary and are design dependant. Please note the preface. Partial extractions from the data sheets may lead to an incorrect equipment selection and specification.
Rev.4.2 / 15.12.2011
Choose your language
